win10 openocd通过vscode远程调试stm32的uboot--Apple的学习笔记-摩杜云开发者社区

一，前言

我在uboot支持的cortex-M4内核启动流程分析--Apple的学习笔记中就说过了，我计划要单步调试uboot，但是我只有stlink，所以要基于openocd的gdb来调试，所以就做了尝试，花费约2天时间，虽然做了些无用功，专门还装了ubuntu18.04，且基于ubuntu还安装了openocd这些其实都无用的，但是就是这些过程，让我了解了openocd这些命令的使用方法，最终我才能在win10上安装openocde，然后通过win10的vscode通过ssh连接ubuntu进行gdb单步调试环境搭建成功。

二，win10 openocd搭配ubuntu中的vscode调试

1，stlink连接开发板，且插入stlink。

2，打开一个cmd输入命令，然后可以看到正常识别到stlink，且等待gdb的3333端口。

openocd -f D:\program\OpenOCD-20231002-0.12.0\share\openocd\scripts\interface\stlink-v2.cfg -f D:\program\OpenOCD-20231002-0.12.0\share\openocd\scripts\target\stm32f4x.cfg -c "bindto 0.0.0.0"

3，用ubuntu本地的vscode来单步调试，作为gdb的客户端。launch.json设置如下

{
    "version":"0.2.0",
    "configurations":[
        {
            "name": "(gdb) Launch",
            "type": "cppdbg",
            "request": "launch",
            "program": "/work/STM32/LED.elf",
            "args": [],
            "stopAtEntry": true,
            "cwd": "${workspaceFolder}",
            "environment": [],
            "externalConsole": false,
            "MIMode": "gdb",
            "miDebuggerPath": "/work/tools/gcc-arm-none-eabi-9-2019-q4-major/bin/arm-none-eabi-gdb",
            "miDebuggerServerAddress":"192.168.112.10:3333",
            /*"preLaunchTask":"build",*/
            "setupCommands": [
                {
                    "description": "Enable pretty-printing for gdb",
                    "text": "-enable-pretty-printing",
                    "ignoreFailures": true
                }
            ]
        }

    ]
}

通过本地vscode用-exec为前缀的gdb命令都是可行的。 注意，连接openocd后，先要暂停，否则报错如下

-exec load u-boot
Unable to perform this action because the process is running.

正常的调试信息如下

-exec load /work/STM32/LED.elf
Loading section .isr_vector, size 0x188 lma 0x8000000
1045+download,{section=".isr_vector",section-size="392",total-size="55434"}
1045+download,{section=".isr_vector",section-sent="392",section-size="392",total-sent="392",total-size="55434"}
Loading section .text, size 0xf1c lma 0x8000188
1045+download,{section=".text",section-size="3868",total-size="55434"}
Loading section .rodata, size 0x10 lma 0x80010a4
1045+download,{section=".rodata",section-size="16",total-size="55434"}
Loading section .ARM, size 0x8 lma 0x80010b4
1045+download,{section=".ARM",section-size="8",total-size="55434"}
Loading section .init_array, size 0x4 lma 0x80010bc
1045+download,{section=".init_array",section-size="4",total-size="55434"}
Loading section .fini_array, size 0x4 lma 0x80010c0
1045+download,{section=".fini_array",section-size="4",total-size="55434"}
Loading section .data, size 0x54 lma 0x80010c4
1045+download,{section=".data",section-size="84",total-size="55434"}
Loading section .mysec, size 0x4 lma 0x8001118
1045+download,{section=".mysec",section-size="4",total-size="55434"}
Start address 0x8000fc4, load size 4380
Transfer rate: 6 KB/sec, 547 bytes/write.
-exec b main
Note: breakpoints 1 and 2 also set at pc 0x80005e6.
Breakpoint 3 at 0x80005e6: file Src/Core/Src/main.c, line 77.
c
Cannot evaluate expression on the specified stack frame.

Breakpoint 1, main () at Src/Core/Src/main.c:77
halted: PC: 0x08000f44

Program received signal SIGINT, Interrupt.
0x08000f92 in HAL_GetTick () at Src/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal.c:325
Kill the program being debugged? (y or n) [answered Y; input not from terminal]
[Inferior 1 (Remote target) killed]
The program '/work/STM32/LED.elf' has exited with code 0 (0x00000000).

三，win10 openocd搭配ssh连接的vscode远程调试

只是不清楚用ssh连接的远程vscode为什么不行，理论上本地vsocode可行，远程vscode也可行，我有了如上使用经验，也就是说了解了各种问题解决方案，于是又进行了尝试。

1，win上的操作和之前一样，且先将vscode和ubuntu14.04连接上。 a，stlink连接开发板，且插入stlink b xxx，打开一个cmd输入命令，然后可以看到正常识别到stlink，且等待gdb的3333端口。

openocd -f D:\program\OpenOCD-20231002-0.12.0\share\openocd\scripts\interface\stlink-v2.cfg -f D:\program\OpenOCD-20231002-0.12.0\share\openocd\scripts\target\stm32f4x.cfg -c "bindto 0.0.0.0"

2，vscode中launch脚本为

{
    "version":"0.2.0",
    "configurations":[
        {
            "name": "(gdb) Launch",
            "type": "cppdbg",
            "request": "launch",
            "program": "/work/v9/u-boot-2023.10/stm/u-boot",
            "args": [],
            "stopAtEntry": true,
            "cwd": "${workspaceFolder}",
            "environment": [],
            "externalConsole": false,
            "MIMode": "gdb",
            "miDebuggerPath": "/work/tools/gcc-arm-none-eabi-9-2019-q4-major/bin/arm-none-eabi-gdb",
            "miDebuggerServerAddress":"192.168.112.10:3333",
            /*"preLaunchTask":"build",*/
            "setupCommands": [
                {
                    "description": "Enable pretty-printing for gdb",
                    "text": "-enable-pretty-printing",
                    "ignoreFailures": true
                }
            ]
        }

    ]
}

然后vscode中按F5，就连接上了远程openocd的3333，然后要先按暂停，之后laod 全路径才能成功下载u-boot，再reset和halt停止到入口，就可以单步或全速运行，通过界面方式打断点，也可以用-exec b来打断点调试。

-exec load /work/v9/u-boot-2023.10/stm/u-boot
-exec monitor reset halt

win10 openocd通过vscode远程调试stm32的uboot--Apple的学习笔记_openocd远程调试

四，小结

我的uboot单步调试目标终于完成了。因为之前qemu无法调试am335x，所以看到stm32F4居然也有uboot，而我是有此芯片的开发板加stlink-v2调试器的，只是应该需要修改设备树的，否则板子不同。所以我就想到用openocd作为调试器的gdbserver端口，然后vscode通过gdbclient来进行单步调试uboot核心流程，作为进一步深入理解的闭环验证工具链。调试环境搭建完工，不用再printf了，调试速度立马升级，分析代码的难度立马降级，哈哈~